Datei:Usbkey internals.jpg
Originaldatei (1.000 × 959 Pixel, Dateigröße: 490 KB, MIME-Typ: image/jpeg)
Diese Datei stammt aus Wikimedia Commons und kann von anderen Projekten verwendet werden. Die Beschreibung von deren Dateibeschreibungsseite wird unten angezeigt.
The internal components of a typical keydrive
This photograph shows both sides of the printed circuit board inside a typical keydrive (Seitec USB-BAR USB 1.1circa 2004), in this case an inexpensive 64 Mbyte USB2.0 device. The plastic clamshell case has been removed.
In practice the keydrive consists of only two significant components. The first is the flash memory part (item 4 in the diagram), a generic device that might as easily be found in a digital camera's memory card. The second (item 2 in the diagram) is a device which implements the USB networking and mass-storage interface, and which knows how to make a chunk of generic flash memory appear like a normal disk drive. The high degree of integration in this latter part makes small, inexpensive keydrives possible.
The parts of the device are as follows:
- A male type-A USB connector.
- An Ours Technology Inc. OTi-2168 USB 2.0 mass storage controller. This implements the USB 2.0 host controller, and provides a seamless linear interface to block-oriented serial flash devices, while hiding the complexities of block-orientation, block erasure, and wear balancing. It contains a small RISC microprocessor and a small amount of ROM and RAM. This communicates with the Hynix device over an 8-line unified address/data bus. This version is a 7x7mm 48-pin LQFP (Low Profile Quad Flat Pack) surface-mount device (info).
- JP1 and JP2: two unpopulated 10-pin connectors, used for testing during the keydrive's manufacture.
- A Hynix Semiconductor HY27USxx121M series NAND Flash memory device, featuring 4096 independently erasable blocks each providing 16 Kbytes of storage, yielding a total of 64 Mbytes of usable storage. The version used in this keydrive is a 20x12mm 48-pin TSOP1 (Thin Small Outline Package) surface-mount package (datasheet) Archivkopie in der Wayback Machine.
- An SKC Shin Chang Electronics 12.000 MHz crystal oscillator (XTAL). The OTi device runs the output of this through a phase-locked loop to produce its main 12 MHz clock signal.
- A single yellow light-emitting diode (run from a pin on the OTi device) which flashes to indicate activity.
- A simple two-position switch, used to indicate whether the device should be in "write-protect" mode. It is shown here in the make position, indicating write-protect is off.
- An unpopulated space for a second TSOP1 memory package. The OTi device is capable of driving up to eight such devices. Having this second space allows the manufacturer to choose (generally on a cost basis) whether to use one or two TSOP flash parts.
Surrounding these main components are a number of tiny surface-mount resistors (many of them serving as pull-ups) and capacitors.
For a closeup of an area of this keydrive, see this image.
Information and licensing
Photographs taken and annotated by John Fader in December 2004 using Adobe Photoshop and Inkscape. This image is (C) Copyright 2004 and (with the exception of its use under the GFDL) all rights are reserved.
Es ist erlaubt, die Datei unter den Bedingungen der GNU-Lizenz für freie Dokumentation, Version 1.2 oder einer späteren Version, veröffentlicht von der Free Software Foundation, zu kopieren, zu verbreiten und/oder zu modifizieren; es gibt keine unveränderlichen Abschnitte, keinen vorderen und keinen hinteren Umschlagtext.
Der vollständige Text der Lizenz ist im Kapitel GNU-Lizenz für freie Dokumentation verfügbar.http://www.gnu.org/copyleft/fdl.htmlGFDLGNU Free Documentation Licensetruetrue |
Diese Datei ist unter der Creative-Commons-Lizenz „Namensnennung – Weitergabe unter gleichen Bedingungen 3.0 nicht portiert“ lizenziert. | ||
| ||
Diese Lizenzmarkierung wurde auf Grund der GFDL-Lizenzaktualisierung hinzugefügt.http://creativecommons.org/licenses/by-sa/3.0/CC BY-SA 3.0Creative Commons Attribution-Share Alike 3.0truetrue |
Originally uploaded by John Fader 17:59, 4 December 2004
In dieser Datei abgebildete Objekte
Motiv
Dateiversionen
Klicke auf einen Zeitpunkt, um diese Version zu laden.
Version vom | Vorschaubild | Maße | Benutzer | Kommentar | |
---|---|---|---|---|---|
aktuell | 13:23, 7. Jul. 2008 | 1.000 × 959 (490 KB) | wikimediacommons>Samulili | better |
Dateiverwendung
Die folgende Seite verwendet diese Datei:
Metadaten
Diese Datei enthält weitere Informationen, die in der Regel von der Digitalkamera oder dem verwendeten Scanner stammen. Durch nachträgliche Bearbeitung der Originaldatei können einige Details verändert worden sein.
Kameraausrichtung | Normal |
---|---|
Horizontale Auflösung | 72 dpi |
Vertikale Auflösung | 72 dpi |
Software | Adobe Photoshop 7.0 |
Speicherzeitpunkt | 16:51, 4. Dez. 2004 |
Farbraum | Nicht kalibriert |